Seized brake calipe...
 

  You don't need to be an 'investor' to invest in Singletrack: 6 days left: 95% of target - Find out more

[Closed] Seized brake caliper (Nissan Micra)

12 Posts
9 Users
0 Reactions
86 Views
Posts: 0
Free Member
Topic starter
 

Need to change the brakes and discs on her car and I have realised the calliper is quite stiff and hard to push back. Is there a way of unseizing it or should I just replace the calliper and bleed the system? I'd rather aviod having to bleed but if it's easier and quicker, i'll have to as she needs the car for work.

Thanks in advance


 
Posted : 28/04/2013 6:53 pm
Posts: 39449
Free Member
 

You can free them off but imo you need to replace them as they sieze again quickly


 
Posted : 28/04/2013 7:00 pm
Posts: 39449
Free Member
 

That is of course if its siezed. Most Car brakes do need a chunk of effort to get em back !


 
Posted : 28/04/2013 7:03 pm
 br
Posts: 0
Free Member
 

It may rotate out/in rather than just straight out/in, my old 405 was like that.

Otherwise just put the old stuff back on and get a new (or s/h) caliper - not dear.


 
Posted : 28/04/2013 7:16 pm
Posts: 0
Free Member
 

bleeding car brakes is a piece of cake. easier than a mtb

if the piston is stiff buy a new caliper. Free them up works short term but it will seize and destroy the new pads/disc which will cost you more ££££ in the long run


 
Posted : 28/04/2013 8:43 pm
Posts: 1617
Free Member
 

yup, check it's not a wind in piston if it's a rear one.

If it s faulty get some refurb ones. Much less hassle than trying to sort them and myou can be confident they will be reliable.


 
Posted : 28/04/2013 9:11 pm
Posts: 65918
Free Member
 

Yeah, I fannied around with used ones before realising that refurbs were only about £20 more.


 
Posted : 28/04/2013 9:15 pm
Posts: 0
Free Member
Topic starter
 

Cool thanks guys, I'll get some new callipers instead. they're not that much I don't think.


 
Posted : 28/04/2013 9:19 pm
 JCL
Posts: 0
Free Member
 

Or you could just clamp the hose, drive the piston out, clean the surface corrosion off, put it back together, and it could be great for 3 years like mine has been.


 
Posted : 28/04/2013 9:19 pm
Posts: 0
Free Member
Topic starter
 

does it matter that there is a nick in the rubber boot around the piston?


 
Posted : 28/04/2013 9:41 pm
 JCL
Posts: 0
Free Member
 

Depends how bad. You can always just get that one seal. If you filled the boot with heavy grease it would be fine for ages I bet.


 
Posted : 29/04/2013 3:30 pm
Posts: 0
Free Member
 

If you filled the boot with heavy grease it would be fine for ages I bet.

Then you'd die. Or kill someone else.

Unless the grease was specifically designed for brake caliper use. Do not use mineral greases.


 
Posted : 29/04/2013 3:37 pm
Posts: 0
Free Member
 

Did you try n push back with a bleed screw open ? if not you can't outrule a collapsed flexy hose , more than likely the caliper but saves spending extra money.


 
Posted : 29/04/2013 3:37 pm

6 DAYS LEFT
We are currently at 95% of our target!